Quick Links. Wireless Access Point. Table of Contents. V3 firmware 2.
|Published (Last):||27 November 2013|
|PDF File Size:||3.71 Mb|
|ePub File Size:||2.31 Mb|
|Price:||Free* [*Free Regsitration Required]|
Recommend Documents. The Wireless Access Point is equipped with Introduction 1. Users Manual. Users Manual Programming buttons. In order for HandleEasy to work together with your equipment, it must be 'taught' the signals that are sent from the remote control of. Users Manual This Fluke product will be free from defects in material and workmanship for three DC Millivolts Measurement. Range mV dc. Circuit diagrams. Instruction Manual will assist you to get the most from your machine.
This manual contains Scooter can be found in the rear of this manual ,. E - JINR. Users Manual - Brother Thank you for choosing a Brother electronic typewriter! Some of the outstanding features of this typewriter are illustrated in the letter below. The num-. This report PSD Structural Desktop Users Manual. Title Bar. Section 2: Installation and Setup.
Further, the warranty does not Neve Users Manual. Elix5 users manual. It features an impressive total of 7. WLAP v2 Hierbij verklaart OvisLink Corp. Hereby, OvisLink Corp. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: y Reorient or relocate the receiving antenna. This device complies with Part 15 of the FCC rules. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. All trademarks and brand names are the property of their respective proprietors.
Specifications are subject to change without prior notification. It features an impressive total of 7 wireless multi-function modes that are not available in normal access point. Your network security is therefore double assured. The web-based management utility is provided for easy configuration that your wireless network connection is ensured to be always solid and hassle free. Support data rate automatic fallback. Automatic channel selection. Client access control.
Supports Supports IAPP. ACK Timeout , Watch dog function. Web interface management. Support System event log and statistics. MAC filtering For wireless only. Performing the Factory Reset will erase all previously entered device settings. Please restart your PC to renew the IP address. Usually, the best place for the Access Point is at the center of your wireless network, with line of straight to all your wireless stations.
Also, remember to adjust the antenna; usually the higher the antenna is placed; the better will be the performance. Connect to your local area network: connect an Ethernet cable to one of the Ethernet port. Please ask your dealer for technical support. Please make sure your computer IP is in the same subnet as the AP i. Client Mode. Bridge Mode. WDS Repeater Mode. Universal Repeater Mode. This device is shipped with configuration that is functional right out of the box.
If you want to change the settings in order to perform more advanced configuration or even change the mode of operation, you can use the web-based utility provided by the manufacturer as described in the following sections. All stations can have the Internet access if only the Access Point has the Internet connection. See the sample application below. Refer to the illustration below. You can share files and printers between wireless stations PC and laptop with wireless network adapter installed.
It is mostly used by enterprise to connect 2 remote office's network together. This feature is also useful when users want to bridge networks between buildings where it is impossible to deploy network cable connections between these buildings. But the universal repeater does not require the remote device to have WDS function.
Therefore, it can work with almost any wireless device. However, the output power is divided between 2 wireless sides and proper antenna installation can influence the performance greatly. Start your computer. Connect an Ethernet cable between your computer and the Wireless Access Point.
Make sure your wired station is set to the same subnet as the Wireless Access Point, i. Start your WEB browser. Click on the desired setup item to expand the page in the main navigation page.
The setup pages covered in this utility are described below. Limited not exceed 32 characters. In other words, this device will not be visible by any wireless station. Band You can choose one mode of the following you need.
The default is 2. It is case-sensitive and must not exceed 32 characters. An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network. The default SSID is airlive. Channel Number Allow user to set the channel manually or automatically.
If set channel manually, just select the channel you want to specify. The number of channels supported depends on the region of this Access Point. All stations communicating with the Access Point must use the same channel.
The default channel is Isolation By the function, all wireless clients can't mutual link, but wireless client still link with LAN port adapter. The default value is Disabled. And WLAPv2 also support other wireless authentication and encryption methods for enhance your wireless network.
With Open System authentication, a wireless PC can join any network and receive any messages that are not encrypted. With Shared Key authentication, only those PCs that possess the correct authentication key can join the network. By default, IEEE If you want secure your wireless network, you need to setup wireless security related function to enable security network.
None Encryption: None Encryption is set to None by default. If the Access Point is using Encryption None, then the wireless adapter will need to be set to the same authentication mode.
Air Live WL-5450AP User Manual
Manual zz. WLAP v2 Hierbij verklaart OvisLink Corp. Hereby, OvisLink Corp. The author of the software does not provide any warranty. This does not affect the warranty for the product itself.
Slovensky - Air Live WL-5460AP v2 Quick Setup Manual
AirLive WL-5460APv2 e9 User's Manual